TEKNODUR 3510-23
Two-component topcoat.
Two-component reaction drying topcoat for synthetics and MDF.
Resistant to weak acids, bases, and solvents. Re-coating must be carried out within max. 36 hours, as otherwise poor adhesion between the layers may be the result. Application of silk screen-printing must be carried out within 24 hours to obtain sufficient adhesion. For internal use if an abrasion resistant and robust surface is required.
Technical data sheet
Safety data sheet
- TEKNODUR 3510-23_BASE 3_2024-05-15_EU_en
- TEKNODUR 3510-23_BASE 3_2024-05-15_GB_en
- TEKNODUR 3510-23_BASE 3_2024-05-15_IE_en
- TEKNODUR 3510-23_BASE 3_2024-05-15_MT_en
- TEKNODUR 3510-23_BASE 3_2024-05-15_NI_en
- TEKNODUR 3510-23_TS 0001 HVID BASE 1_2022-10-13_EU_en
- TEKNODUR 3510-23_TS 0001 HVID BASE 1_2022-10-13_GB_en
- TEKNODUR 3510-23_TS 0001 HVID BASE 1_2022-10-13_IE_en
- TEKNODUR 3510-23_TS 0001 HVID BASE 1_2022-10-13_MT_en
- TEKNODUR 3510-23_TS 0001 HVID BASE 1_2022-10-13_NI_en
- TEKNODUR 3510-23_TS 0002 HVID BASE 2_2023-06-06_EU_en
- TEKNODUR 3510-23_TS 0002 HVID BASE 2_2023-06-06_GB_en
- TEKNODUR 3510-23_TS 0002 HVID BASE 2_2023-06-06_IE_en
- TEKNODUR 3510-23_TS 0002 HVID BASE 2_2023-06-06_MT_en
- TEKNODUR 3510-23_TS 0002 HVID BASE 2_2023-06-06_NI_en
Application
MIXING OF THE COMPONENTS:
To achieve a satisfactory result, it is important that the hardener is mixed correctly. Inadequate stirring or incorrect mixing ratio results in imperfect curing and impaired film properties. Within the first 15 minutes following the addition of hardener, the viscosity increases. Final adjustment of the spraying viscosity must be made after this time.
Application conditions
The surface to be treated must be dry. During the application and drying period the temperature of the ambient air shall be above +10°C and the relative air humidity below 80%.
Adhesion and compatibility to plastic types should be tested before application as variation may occur, dependent upon the type of plastic.
Storage
The storage stability is shown on the label. Store in a tightly closed container.
| Solids | abt. 42 % by volume |
|---|---|
| Total mass of solids | abt. 769 g/l |
| Volatile organic compound (VOC) | abt. 507 g/l |
| Pot life | 3h (+23 °C) |
| Mixing ratio | 4,2:1 by volume (comp. A : comp. B) |
| Hardener | Comp. B: TEKNODUR HARDENER 7340-00 |
| Tinting system | Teknotint |
| Drying time – dust free | Approx. 15 min. (ISO 1517) |
| Drying time – touch dry | Approx. 1 h (ISO 3678) |
| Drying time – forced drying | +80°C / 50% RH - through dry: 20 min. |
| Thinner | Standard thinner: TEKNOSOLV 6220-00. Fast thinner: TEKNOSOLV 7120-00. |
| Clean up | TEKNOSOLV 6220-00 |
| Colours | Available in colours according to RAL, NCS S or other colour cards. |
| Safety markings | See safety data sheet. |