TEKNORAN COMBI 1485-09
Single coat paint based on oxirane ester
TEKNORAN COMBI 1485-09 is a two-component, isocyanate-free single coat paint with high solids content and based on oxirane ester. Contains active anti-corrosive pigments. Product coating on steel surfaces within the engineering industry. The solvent emissions of the paint are low due to the high volume solids content.
Product coating on steel surfaces within the engineering industry. The solvent emissions of the paint are low due to the high volume solids content. The paint dries both in elevated and in room temperatures. Welding of the painted surface is to be avoided.
The paint dries both in elevated and in room temperatures. Welding of the painted surface is to be avoided.
Surface preparation
Remove from the surfaces any contaminants that might be detrimental to surface preparation and application. Remove also water-soluble salts by using appropriate methods. The surfaces are prepared according to the different materials as follows:
STEEL SURFACES: Remove mill scale and rust by blast cleaning to preparation grade Sa 2½ (standard ISO 8501-1). Roughening the surface of thin-plate improves the adhesion of the paint to the substrate. When using chemical pretreatment the suitability of the treatment is to be checked from the paint manufacturer.
ZINC SURFACES: Hot-dip-galvanized steel structures that are exposed to atmospheric corrosion can be painted if the surfaces are sweep blast-cleaned (SaS) till matt all over. Suitable cleaning agents are, e.g. aluminium oxide and natural sand. It is not recommended according to standard ISO 12944-5 to paint hot-dip-galvanized objects that are subjected to immersion strain. Painting of hot-dip-galvanized objects that are subjected to immersion strain must be discussed separately with Teknos. It is recommended that new zinc-coated thin-plate structures are treated with sweep blast-cleaning (SaS). Thin-plate surfaces that have been weathered to matt can be treated also with RENSA STEEL washing agent.
ALUMINIUM SURFACES: Treat the surfaces with RENSA STEEL washing agent. Surfaces that are exposed to weathering are also roughened up with sweep blast-cleaning (AlSaS) or sanding.
OLD PAINTED SURFACES SUITABLE FOR OVERCOATING: Any impurities that might be detrimental to the application of paint (e.g. grease and salts) are removed. The surfaces must be dry and clean. Old, painted surfaces that have exceeded the maximum overcoating time are to be roughened as well. Damaged parts are prepared in accordance with the requirements of the substrate and the maintenance coating.
The place and time of the preparation are to be chosen so that the prepared surface will not get dirty or damp before the subsequent treatment.
Additional instructive information for surface preparation can be found in standards EN ISO 12944-4 and ISO 8501-2.
KORRO PVB Prefabrication Primer and KORRO E Epoxy Prefabrication Primer can be used, when required.
Application
Take into consideration the pot life of the mixture when estimating the amount to be mixed at a time. Before application the base and hardener are mixed in right proportion. Stir thoroughly down to the bottom of the vessel. Inadequate stirring or incorrect mixing ratio results in imperfect curing and impaired film properties.
Apply preferably by airless spray as only this method provides the recommended film thickness in a single operation. Suitable airless nozzle size 0.011 - 0.013". Brush can be used for touching up and painting small areas.
Slow thinner: TEKNOSOLV 1640. Used e.g. when painting large surfaces and when the temperature is above room temperature.
Fast thinner for electrostatic spraying: TEKNOSOLV 1639.
Application conditions
The surface to be treated must be dry.
During the application and drying period the temperature of the ambient air, the surface and the product shall be above +5°C and the relative air humidity below 80%.
Storage
The storage stability is shown on the label. Store in a cool place and in tightly closed containers.
| Solids | abt. 68 % by volume |
|---|---|
| Total mass of solids | abt. 1300 g/l |
| Volatile organic compound (VOC) | abt. 265 g/l |
| Pot life | 4 h (+23 °C) |
| Mixing ratio | 2:1 by volume (comp. A : comp. B) |
| Hardener | Comp. B: TEKNORAN HARDENER 1475-00 or TEKNORAN HARDENER 1475-51 |
| Tinting system | Teknotint |
| Practical spreading rate | The values depend on the application technique, surface conditions, overspray, etc. |
| Drying time – dust free | 1 h (ISO 9117-3:2010) |
| Drying time – touch dry | 4 h (DIN 53150:1995) |
| Drying time – forced drying | +80°C / 30 min. |
| Thinner | Standard thinners: TEKNOSOLV 9511, TEKNOSOLV 6622 and TEKNOSOLV 6120-00. Other thinners suitable for the product: see Application. |
| Clean up | TEKNOSOLV 9511, TEKNOSOLV 6622, TEKNOSOLV 6120-00. |
| Colours | By agreement. |
| Packages | Available in a range of standard pack sizes. |
| Safety markings | See safety data sheet. |