AKRYLIN

Facade paint

  • Water-borne

Water-borne, eco-friendly outdoor paint with a high-quality acrylate dispersion binder. Finish: semi-matt.

For wooden facades of houses and outbuildings. Also suitable for galvanized surfaces such as drainpipes. For log surfaces we recommend WOODEX AQUA CLASSIC wood stain. Suitable for new and previously with acrylate paints painted surfaces. May also be used for maintenance painting on most old oil and alkyd paints, if the surfaces are in good condition. NOTE! For surfaces previously painted with red ochre paint we recommend new treatment with red ochre paint.

Technical data sheet

Safety data sheet

Product colour chart

Surface preparation

NEW WOODEN SURFACE: Treat the surface as soon as possible. At least the impregnation and priming would be best done in the summer of construction. Remove from the surface all loose matter, dirt, dust and mildew. If needed, use RENSA FACADE facade cleaner. Apply a coat of clear wood preservative from the WOODEX series. Allow to dry for one day. Prime wooden surfaces with NORDICA PRIMER and allow the surfaces to dry for 1 - 3 days depending on the weather. Wash the metal parts with TEKNOSOLV 1621 (solvent naphtha) and prime with FERREX AQUA. PREVIOUSLY PAINTED OR OLD WOODEN SURFACE: Change the deteriorated wooden parts to new ones. Remove loose matter, dirt and dust. Remove the deteriorated paint coats entirely. Note, that the adherence of an old thick paint layer to the substrate may have been weakened, therefore the paint should be removed although the paint film looks intact. The old paint layer is removed primarily by scraping or wire brushing and possibly by heating the surface with infra-red heater designed for that purpose. Secondarily paint remover or blasting can be used. The surface of old oil paint coats may be in poor condition: heavily chalked, dusty and brittle. These types of surfaces must be carefully cleaned so, that the new paint adheres properly to the substrate. Some traditional paint types, such as red ochre paint and paraffin oil paint, produce such a brittle and dusty surface, that they can't be maintenance painted with AKRYLIN. If there is doubt about the adhesion, it must be ensured by test painting. Wash surfaces with RENSA FACADE facade cleaner and rinse thoroughly. Old, untreated wooden surfaces can before the priming be treated with clear wood preservative from the WOODEX series, see ´NEW WOODEN SURFACE´. Prime bare wooden surfaces with NORDICA PRIMER. Allow to dry for 1 to 3 days depending on the weather. Wire-brush the rusty metal parts. Wash all metal parts with TEKNOSOLV 1621 (solvent naphtha) and prime with FERREX AQUA.

Application

Reserve a sufficient amount of paint in the same vessel for each uniform surface. Colour differences will thus be avoided. Stir the paint well and apply by paint brush or spray once or twice. If the paint is applied by spray, the surface is to be finished by a brush to ensure the adhesion.

Application conditions

The surface to be painted must be dry. The moisture of the wood must be below 20% of the dry weight of the wood. During the application and drying period the temperature of the ambient air, the surface and the paint shall be above +5°C and the relative air humidity below 80%. Avoid application in direct sunlight.

Storage

Must not freeze.
Solids abt. 35 % by volume
Volatile organic compound (VOC) EU VOC limit value (kat A/d): 130 g/l. The product's VOC: max. 130 g/l.
Gloss Semi-matt
Tinting system Teknomix
Density abt. 1.2 g/ml
Practical spreading rate Planed timber: 8 - 10 m²/l. Sawn timber: 6 - 8 m²/l.
Drying time – touch dry 1 h
Drying time - overcoatable 2 - 4 h
Thinner Water.
Clean up Warm water and RENSA BRUSH brush cleaner. Wash the equipment immediately after use.
Colours According to the Colour Cards for exterior paints.
Weather resistance Weather resistance: very good.
Packages Base paints 1 and 3: 0,9 L, 2,7 L, 9 L, 18 L. Base paint 5: 9 L.
Safety markings See safety data sheet.