TEKNOFLOOR AQUA MINOTOP 6760-10
Water-borne 2C sealing coating for mineral substrates for interior use
- 2-component
- Water-borne
- Sealer
- 2-component
- Water-borne
- Sealer
TEKNOFLOOR AQUA MINOTOP 6760-10 is a water-borne, highly abrasion-resistant 2C PU floor sealing coating for the treatment of interior mineral floors. The product is resistant to light and yellowing. TEKNOFLOOR AQUA MINOTOP 6760-10 has a good moisture resistance. The anti-slip property of the coating can be classified as "safe" in compliance with DIN 51131.
Technical data sheet
Safety data sheet
- TEKNOFLOOR AQUA MINOTOP 6760-10_FARBLOS-INCOLORE-COLOURLESS_2026-10-29_EU_en
- TEKNOFLOOR AQUA MINOTOP 6760-10_FARBLOS-INCOLORE-COLOURLESS_2026-10-29_IE_en
- TEKNOFLOOR AQUA MINOTOP 6760-10_FARBLOS-INCOLORE-COLOURLESS_2026-10-29_MT_en
- TEKNOFLOOR AQUA MINOTOP 6760-10_FARBLOS-INCOLORE-COLOURLESS_2026-10-29_NI_en
Surface preparation
Every substrate must be well-cleaned, dry and free from grease and oil. Coating removal: Sand
Application
Stir or shake the product well for several minutes before use, if necessary by machine.
Application conditions
Recommended temperature for surroundings and product: +15°C-25°C. Do not apply below +10°C. Ideal surface and object temperature for application: +18°C-22°C. Avoid application in direct sunlight. Underfloor heating systems must be adjusted well in advance.
Maintenance
Initial and maintenance care: After at least 3 weeks curing time with RENSA FLOOR POLISH 4580.
Storage
Storage temperature is +5°C - +30°C. Store in a tightly closed container.
Application methods
Primed surfaces must be sealed within 48 hours.
Please note: Avoid sanding through (staining!).
As anhydrite or cement floors have different properties in terms of material composition, a preliminary test must always be carried out. (Determination of the required material quantity, etc.)
The surfaces to be coated must comply with the structural engineering standards, they must be load-bearing, solid, non-slip and be free from intermediate layers (sintered skins, etc.) that interfere with bonding.
The residual moisture (max. 0.5% without underfloor heating, max. 0.3% with underfloor heating, or according to applicable standards) must be measured and recorded. Turn off underfloor heating 30 hours before sealing.
Floor coatings are generally dry after 24 hours and can be walked on. However, full load-bearing capacity (curing) is only guaranteed after 14-21 days (according to SIA 2535.7.4). Do not lay any carpets or other floor coverings or carry out any surface treatment beforehand. Sealing requires sound technical knowledge.
Do not use in wetrooms.
| Volatile organic compound (VOC) | abt. 66 g/l |
|---|---|
| Pot life | 2 h (+23 °C) |
| Mixing ratio | 5:1 by volume (comp. A : comp. B) |
| Hardener | Mix in hardener mechanically for several minutes. Comp. B: TEKNOFLOOR AQUA HARDENER 1058-99 |
| Theoretical spreading rate | 120 g/m²; 8.3 m²/kg |
| Density | abt. 1.13 g/ml |
| Drying time – dust free | 2 h |
| Drying time – through-dry | 7 d |
| Clean up | Wash the equipment immediately after use. VERDÜNNER 1000-98 |
| Colours | Colourless. |
| Safety markings | See safety data sheet. |
| Gloss value | 10 |